1. What is the port configuration on a Cisco 1603 router?a. 1 Ethernet, serial portb. 1 Ethernet and 1 synchronous 56 Kbps serial port with integrated CSU/DSUc. 1 Ethernet and 1 BRI S/T portd. 1 Ethernet, 1 FDDI, and 1 BRI U port
2. What is the total bandwidth available on an ISDN BRI circuit?a. 256 Kbpsb. 64 Kbpsc. 128 Kbpsd. 56 Kbps
3. What command will show the modem configured on a line?
4. What command set should be used to correctly configure a US Robotics modem with a known modem string on a Cisco access server?
5. How many B channels are available in an ISDN BRI circuit?a. 1b. 2c. 3d. 4
6. Which of the following points is the boundary for Non-US ISDN circuits?a. Tb. Rc. Sd. U
7. What command will set up a static route from 172.21.3.0 to 172.21.100.0 given a subnet mask of 255.255.255.0 and a gateway address of 172.21.3.1?
8. What command is used to enable the predictor compression algorithm on an interface?
9. Which of the following ISDN channels controls call setup, signaling and call termination?a. Db. Ac. Bd. C
10. How many slots for network modules or WAN Interface cards are available on a Cisco 3640 router?a. 1b. 2c. 3d. 4
11. What is a DCE?a. Data Circuit-Terminating Equipmentb. Digital Circuit Equipmentc. Data Circuit Endpointd. Digital Circuit-Terminating Endpoint
12. What command will establish a reverse telnet connection to the modem on line 3?
13. What command sets up a backup interface?
14. Which of the following terminal services are provided by Cisco RAS?a. Telnet/rloginb. X.25 PADc. LATd. TN3270e. PAP Authentication
15. What command enables ppp encapsulation?
16. What command will enable Multilink PPP on an interface?
17. Which of the following are permanent profiles provided by the Cisco 700 Series router?a. Standardb. Externalc. Internald. LAN
18. Which of the following is used to describe the process of Cisco NAT using a single IP address to represent multiple workstations?a. Proxy translationb. Masqueradingc. IP overloadingd. Overloading*
19. Which feature provides the capability for links to terminate at multiple routers with different remote addresses?a. Fast Etherchannelb. Multilink pppc. ISLd. Multichassis Multilink PPP
20. What command will establish a terminal session with an IBM host via TN3270 (2)?
21. What is the line number of the CON port?a. 0b. 1c. 2d. Last TTY line number plus 1
22. What command will enable Dial-on-Demand routing on an asynchronous interface?
23. Which of the following is true of Frame Relay DLCI?a. It is a frame sent from the Frame-Relay switch to the destination router when network congestion is detectedb. It is the frame sent from the Frame-Relay network to a router when the network is congestedc. It is the rate at which a Frame-Relay switch agrees to transfer datad. It is the logical virtual circuit between Customer Equipment and the Frame-Relay network
24. When should modem auto-configuration be used?a. To be able to configure a modem without sending modem configuration commandsb. To allow modem configuration commands to be sent through a terminal emulatorc. To configure modem devices that are not currently supported by Ciscod. To allow for the auto-discover of modems
25. What command should be used to change TN3270 directives into dumb terminal commands?a. ttyhatb. keymapc. ansi.sysd. ttycap26. What WICs does the Cisco 1602 router support?a. Serialb. ISDN BRI S/T, ISDN BRI U, and serialc. ISDN BRI S/T, and seriald. ISDN BRI U
27. What portion of a dialer profile is responsible for all the configuration parameters associated with a particular destination?a. dialer interfaceb. dialer managerc. dialer map classd. dialer pool
28. Which of the following ISDN elements represents the ISDN terminal equipment?a. NT2b. TE1c. LEd. NT1
29. What command should be used to specify that the serial line is connected by a non-V.25bis modem using EIA signaling only. Specifically, the DTR signal?a. dialer stringb. dialer v.25c. dialer in-bandd. dialer dtr
30. What command is used to enable incoming network connection to asynchronous ports?
31. What is the total bandwidth available on a European ISDN PRI circuit?a. 1.544 Mbpsb. 2.048 Mbpsc. 4 Kbpsd. 128 Kbps
32. What command will display 12f protocol errors?
33. Which remote access method allows a user to take direct control of a workstation through a dialup line?a. Remote Virtual Connectionsb. Remote-Gatewayc. Remote-Noded. Remote-Control
34. What command will display information on both B channels of BRI interface 2?
35. Which of the following is an example of Cisco protocol translation?a. translate ip 172.21.3.4 lat x25 123555222b. translate ip lat 172.21.3.4 vax11c. translate ip lat 172.21.3.4 x25 1235552222d. translate tcp 172.21.3.4 x25 1235552222
36. Which of the following is true of the ISDN S/T reference point?a. RS-232 connector using pins 2,3,6,20b. RJ-45 connector using pins 3,4,5,6c. RJ-45 connector using pins 1,2,7,8d. V.35 connector using pins 2,3,6,20
37. What is the purpose of implementing a UART?a. isdn framingb. store configurationc. asynchronous port controllerd. synchronous clocking
38. Which of the following memory types is used to hold the router IOS image?a. ROMb. Flashc. RAMd. NVRAM
39. Which of the following routers supports a BRI connection and would be appropriate for a single user or a small office?a. Cisco 200b. Cisco 700c. Cisco 900d. Cisco 1000e. Cisco 1600
40. What command defines the global default pooling mechanism used to supply IP addresses?
41. Which of these points is between the NT1 and LE?a. Rb. Uc. Sd. T
42. A ______ could be configured to avoid dialing caused by routing updates on a DDR interface.a. dynamic routeb. static routec. link state routing protocold. route slowdown
43. What command will allow asynchronous protocol features on VTY lines?
44. What IOS feature allows the increase in the interval for routing protocol updates?a. RIPb. RTMPc. Snapshot routingd. IGRP
45. Which type of line on access servers is typically used to log into the server for configuration purposes?a. CONb. TTYc. VTYd. AUX
46. What command troubleshoots VPDN operation?
47. What command will create a static route from IPX network 30 to IPX network 50 through the router interface 50.0000.0c07.00c2?
48. Which of the following dialer objects is a group of one or more physical interfaces associated with a specific Dialer Profile?a. Physical Interfaceb. Dialer Map-Classc. Dialer Interfaced. Dialer Pool
49. Which of the following ISDN channels would be used for HDLC and PPP?a. Cb. Bc. Dd. A
50. What command sends logging information to a UNIX syslog server?51. What command is used to set the line code type on an ISDN PRI interface?
52. What are the two types of authentication most commonly used with PPP?a. CHAPb. RC4c. L2Fd. PAP
53. What command would configure your router to bring up an additional interface when the load on the DDR interface exceeds 50% in either direction?
54. What is the term for an ordered pool of physical interfaces used by a dialer profile?a. dialer interfaceb. dialer managerc. dialer poold. dialer map class
55. What command configures a router to accept On-Demand Routing routes from stub routers?
56. Which of the following points is between the NT1 and NT2 device?a. Tb. Rc. Sd. U
57. What command verifies Auto Configuration operations?
58. Which of the following memory types is used to hold power-up diagnostics and bootstrap program?a. ROMb. Flashc. NVRAMd. RAM
59. What bandwidth is available with V.32 bis without compression?a. 14.4 Kbpsb. 28.8 Kbpsc. 33.6 Kbpsd. 1200 bps
60. What command, when executed on a Cisco access server, will verify the controller for your channelized T1 is running and no alarms have been reported?
61. What commands will display information about open LAT, Telnet, or rlogin connections?
62. What command will configure a local pool of IP addresses?
63. What is the port configuration of a Cisco 1602 router?a. 1 Ethernet, and 1 BRI S/T portb. 1 Ethernet, serial portc. 1 Ethernet, and 1 synchronous 56 Kbps serial port with integrated CSU/DSUd. 1 Ethernet, 1 FDDI, and 1 BRI U port
64. Which of these services are provided by Cisco NAT?a. Tcp load distributionb. Domain name lookupc. Address resolutiond. Static address translation
65. Which of these dialer objects contains information specific to the call setup?a. Dialer Interfaceb. Dialer Map-Classc. Physical Interfaced. Dialer Pool
66. What is the total bandwidth available on an ISDN BRI circuit including D channels?a. 56 Kbpsb. 64 Kbpsc. 128 Kbpsd. 144 Kbps
67. How many ISDN D channels are available in a European ISDN PRI circuit?a. 1b. 2c. 3d. 4
68. Which of these ISDN elements represents the customer premises switching equipment?a. TE1b. NT1c. NT2d. LE
69. What command sets a low speed interface to asynchronous mode?
70. Which of these commands is similar to the ‘show sessions’ command?a. whereb. show linesc. show buffersd. show interfaces
71. How do you configure Windows 95 to connect as a remote dial-up client?a. Select My Computer, then select Make New Connectionb. Select Install TCP/IP, then select create PPP connectivityc. Select My Computer, then select Dialup Networking, then select Make New Connectiond. Select Network Neighborhood, then select Dialup Networking, then select Make New Connection
72. Which of the following are Cisco Access Services?a. Remote-Node Servicesb. Protocol Translation Servicesc. Asynchronous Routing Servicesd. Remote Control Servicese. Terminal Services
73. What key sequence will switch between sessions if multiple connections are established from a router to a remote host via telnet?
74. What WICs does the Cisco 1601 router support?a. ISDN BRI S/T, and serialb. ISDN BRI Uc. ISDN BRI S/T, ISDN BRI U, and seriald. Serial
75. What are the two primary differences between Dial on Demand Routing and Dial Backup?a. Dial Backup is used when a primary link goes downb. Dial on Demand only works with PPPc. Dial on Demand routing is only used when interesting traffic is received on the interfaced. Dial backup uses interesting traffic to determine when a line goes down76. Which of the following are ISDN switch types used in North America?a. basic-net3b. basic-nilc. basic-5e22d. basic-dms100
77. Which type of line on access servers is the same as an asynchronous interface and is typically used for remote-node dial-in sessions?a. AUXb. VTYc. CONd. TTY
78. What command will create a pool of internal IP addresses to be used by Cisco NAT?
79. What command should be entered to diagnose an integrated modem that may not be functioning properly?
80. Which parameter can be used with a static routing configuration that specifies a route will not be removed, even if an interface shuts down?a. stickyb. staticc. nonvolatiled. permanent
81. Which of these dialer objects are components of a dialer profile?a. interface mapb. dialer interfacec. dialer map classd. dialer pool
82. What command will execute a menu named ‘file’ when user Elvis logs in?
83. When the NAT Overloading feature is implemented, one inside global address represents multiple inside local addresses. How is this feature implemented?a. TCP port numbers are modifiedb. Internal addresses are incremented one per userc. IP address routing tables are modifiedd. The QOS field is modified
84. Which of these compressions standards are supported by Cisco IOS Release 10.3?a. Stacb. Zipc. V.32bisd. Predictor
85. Which dialup networking protocols are supported by Windows 95?a. RASb. PPPc. Novell NetWare Connectd. SNAe. SLIP
86. Which of these points is the boundary for US ISDN circuits?a. Tb. Rc. Ud. S
87. What is the purpose of DHCP?a. Resolve the MAC address into an IP addressb. Dynamically boot computers from the networkc. Dynamically assign a MAC address to computersd. Dynamically assign an IP address to computers
88. What command displays events that are part of NORMAL tunnel establishment or shutdown in VPDN?
89. What command would be used to reset the NAT translations from the translation table?
90. What command is used to configure SPID numbers on a router?
91. Which of the following are types of remote access to network resources?a. Remote Virtual Connectionsb. Remote-Gatewayc. Remote-Controld. Remote-Node
92. What command will apply a single interface configuration to multiple interfaces?
93. What command is used to set the terminal baud rate on async lines?
94. Which of the following is true of Frame Relay FECN and/or BECN?a. Logical virtual circuit between Customer Equipment and Frame-Relay networkb. Frame sent from the Frame-Relay network to a router when the network is congestedc. The rate at which a Frame-Relay switch agrees to transfer datad. Signaling between Customer Equipment and Frame-Relay network responsible for connection management and maintaining status
95. What command string is used to load factory settings on a modem?a. ATb. AT&M0c. AT&Fd. AT&D
96. Which of the following services does Cisco Access Server providea. Serves as a protocol translatorb. Servers as a switchc. Servers as a routerd. Serves as a terminal server
97. What command is used to look at system statistics for all modems installed in an access server?
98. What is the critical advantage of using CHAP instead of PAP authentication?a. PAP is not supported for PPP authenticationb. PAP will disconnect if authentication failsc. PAP sends passwords in clear text formatd. Less packets are transmitted to complete authentication when using CHAP
99. How many slots for network modules or WAN Interface cards are available on a Cisco 3620 router?a. 1b. 2c. 3d. 4
100. What effect does the command ‘ppp authentication chap pap callin’ have?a. This is not a valid commandb. Authentication will be performed for inbound and outbound connectionsc. Enables both CHAP and PAP-CHAP authentication is performed before PAPd. Enables both CHAP and PAP-PAP authentication is performed before CHAP